NGTO Message Board
Welcome to NGTO!
Home ] [ Membership ] [ Donations ] [ Feedback ] [ Stream Reviews ] [ Stream Reports ] [ Maps ] [ Events ] [ Articles ] [ Rules and Regulations ] [ Archives ] Message Board ] FAQ ] [ Hall of Fame ] Sponsors & Supporters ] About ] [ Witticisms ] [ Distinguished Members ]
Welcome to NGTO!

Go Back   NGTO Message Board > Gear Talk > Rod Building
Register Blogs FAQ Members List Calendar Photo Gallery Search Today's Posts Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 11-18-06, 01:28 PM   #1
streamer
Native
 
Join Date: May 2006
Location: Sugar Hill
Posts: 811
Smile How I make cork grips

OK, several people have ask me about how I make my cork grips, so I took a few pics while making one this week, so i could explain it better. I figured I would go ahead and post it for anyone that may want to see.
Note: I'm sure there are others that build them different and better , But this works for me.

pic one - Here is all the stuff I use to build a 7'' grip. Cork rings, 1/4'' threaded rod, washers, nuts and 60min epoxy. All the cork for this grip came from here http://www.lamarfishing.com/


pic two- I have mixed the epoxy and am putting it on both sides of the cork rings (only coat one side of the end rings) I apply the epoxy to the ring and then scrape off as much as i can, leaving a very thin layer of epoxy.


pic three - After putting the epoxy on the rings I slid them on to the treaded rod.


pic four - I have glued all the ring together on the treaded rod, now i put a nut on the other side and tighten it down. I will let the rings dry over night like this.


Pic five- The rings have dried, and now im ready to turn it, Here I have put the threaded rod into my homemade lath, and made sure it is level. Be sure to make sure that it is level. I learned this the hard way Im using a 1x2 block with 60 grit sand paper stapled to it, to get the cork size down closer to the final grip size.


pic six- now I have started using 120 grit sand paper, holding it in my hand and shaping the grip. On this grip, I am tring to match the other one you see in the pic, so I am checking the measurments often.


Pic seven- I have got the grip close to the shape i want so i switch over to 300 to get just how i want it. Once i have the shape perfect i go over it with 600 grit to get it real smooth.


Here's how it turned out


I hope this helps, Im not very good at explaining thing so let me know if you have any questions. Streamer

Last edited by streamer; 11-20-06 at 07:48 AM.
streamer is offline   Reply With Quote
Old 11-18-06, 03:37 PM   #2
FlyBy
Native
 
FlyBy's Avatar
 
Join Date: Dec 2002
Location: Roswell,GA
Posts: 264
Default

Do you use any kind of release agent to make sure that the grip doesn't stick to the threaded rod? Also, can you give some details of the jig that holds your drill? Did you buy it or make it?

Thanks!

FlyBy
__________________
"O, my word, the Trout is perfect in season. Come, I thank you, and here is a hearty draught to you, and to all the Brothers of the Angle..." -Izaak Walton
FlyBy is offline   Reply With Quote
Old 11-18-06, 03:50 PM   #3
streamer
Native
 
Join Date: May 2006
Location: Sugar Hill
Posts: 811
Default

I dont use the a release agent, I just use plyers and turn the grip, it breaks loose easy and then unscrew it off the rod. I have never had a issue with cork breaking.
Here is some pics of the lath i build.


streamer is offline   Reply With Quote
Old 11-18-06, 07:35 PM   #4
FlyBy
Native
 
FlyBy's Avatar
 
Join Date: Dec 2002
Location: Roswell,GA
Posts: 264
Default

Ok, thanks.

What is that shown in the last photo, the sleeve the rod slides into?

FlyBy
__________________
"O, my word, the Trout is perfect in season. Come, I thank you, and here is a hearty draught to you, and to all the Brothers of the Angle..." -Izaak Walton
FlyBy is offline   Reply With Quote
Old 11-18-06, 08:34 PM   #5
rickster
Native
 
Join Date: Sep 2002
Location: Blue Ridge Area
Posts: 666
Default

Pretty slick Streamer , and looks like "on a budget" as well. I like it.

Also, got your P.M. and was not being rude, just real busy. I will give you a call, maybe the week after Thanksgiving.

Again, pretty slick lathe.

rickster
__________________
Every notable advance in the saving work of God among men will, if examined, be found to have two factors present: several converging lines of providential circumstances and a person.
rickster is offline   Reply With Quote
Old 11-19-06, 10:10 AM   #6
streamer
Native
 
Join Date: May 2006
Location: Sugar Hill
Posts: 811
Default

flyby, it a bushing i found at homedepot.

Rickster, no worries.
streamer is offline   Reply With Quote
Old 11-30-11, 10:11 AM   #7
Orangepowerbait
Native
 
Join Date: Oct 2011
Posts: 52
Default

very nice. what type of burl did you use? I see that they offer light, dark and other variations. Do you have any spinner pics?
__________________
Censor me at your own risk!
Orangepowerbait is offline   Reply With Quote
Old 11-20-06, 01:56 PM   #8
Ivan
Native
 
Join Date: May 2000
Location: Alpharetta, Ga, Usa
Posts: 896
Default

Thanks to who ever did this. I think we should sticky some of How to's. There is some good stuff that you guys have posted and I am sure they would be a benifit both new and old builders alike. Again thanks.
__________________
Ivan

Fly Box Outfitters
Fly Fishing School
______________________________________________

Success is the ability to go from one failure to another with no loss of enthusiasm.
"Winston Churchill"
Ivan is offline   Reply With Quote
Old 11-20-06, 02:06 PM   #9
streamer
Native
 
Join Date: May 2006
Location: Sugar Hill
Posts: 811
Default

Wow, my first post to be pinned.


Ivan, I hope this helps you out, you are one of the people i took the pics for, i figured i would go ahead and post it for everyone.
How's the 10wt coming?
streamer is offline   Reply With Quote
Old 11-20-06, 02:11 PM   #10
GonetoSeed
Hall of Fame Member
 
Join Date: Jan 2001
Location: Decatur, Ga, USA
Posts: 1,580
Default

I did the sticky. The first real moderator thing I've done This forum stays cool, calm and collected so no need for deleting, freezing, etc.

Let me know if there are a some others to consider. Some of the How-To posts are mine I think stick them without request would be pretty arrogant.
GonetoSeed is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 04:35 AM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
vB.Sponsors
Copyright 2010 - North Georgia Trout Online - All Rights Reserved